M/s C and I Calibrations Pvt. Ltd, is a NABL Accredited Calibration and Testing Laboratory. The prime aim of this unit is to provide solution in managing calibration and Testing looking to the needs of the various industries in this region govt. organizations and private sectors.
CICPL JAIPUR OFFICE
- J-448, Sitapura Industrial Area, Jaipur-302022 (Raj.) India
- 91-141-2771849 / 91-8003095302
- Mon - Sat: 9:00 am - 6:00 pm
Induced Over- Voltage Withstand Test (DVDF Test):-
This test checks the inter term insulation. For a 11 KV/433 V transformer, 866 volts are applied at the 433 V winding with the help of a generator for 1 minute. This induces 22 KV on 11 KV side. The frequency of the 866 V supply is also increased to 100 Hz.
transformer testing Purpose of Induced over voltage test of transformer:
- To secure that the insulation between the phase windings, turns, coils, tapping leads and terminals.
- For non-uniformity insulated windings the insulation between these parts and earth.
Withstand the temporary over voltages and switching over voltages to which over voltages and switching over voltages subject to the transformer during its lifetime.
- Ensure that the transformer is not cut into one of the electrical supply lines.
This causes the resonant effect to occur, causing high vibration voltage waves that may damage the transformer if there is a weak isolation.
Discovering the air gaps between the layers of the windings to find out the efficiency of insulation between these layers and other layers and high voltage high-frequency we use will detect these air gaps.
Equipment Used :- Motor Generator Test
Our Power and Distribution Transformer Test Laboratory is NABL Accredited & BIS Recognized Laboratory.
Our lab is well equipped, meeting National/ International Standards and accredited by NABL (National Accreditation Board for Testing & Calibration Laboratories) under Dept. of Science & Technology (DST), Govt. of India, New Delhi.
What Is Included
We have included 4 business. These business are below:
We have NABL Accredited & BIS Recognized Power & Distribution Transformer Test Lab. Transformer Tests – As per Is: 1180/ IS: 2026. are Routine Test, Type Test, special Test, Other Test, Lightning Impulse Test on Insulator, Bushing, Current Transformer and Potential Transformer.
The CIPTPL provides dedicated and quality Proficiency Testing Services to its participants. CIPTPL has set up management systems based on ISO/IEC 17043 for this purpose and continually improves upon the effectiveness of the system based on the experience gained in the process.
C and I Calibrations Private Limited was established in 1995. C&I is having State of the art NABL Calibration Accredited Laboratories at Kota and Jaipur. We are also having facilities for Mechanical Calibration, Thermal Calibration, Fluid Flow Calibration & Electro-technical calibration.
C & I Systems is a NABL Accredited Civil Testing Laboratory as per ISO/IEC 17025:2005. Samples are tested here- Soil, Rock, Stone, Water, Steel, Aggregate, Cement, Concrete, CC Cube, Tiles, Brick, Bitumen, Sand, Interlocking Block, Mix Design, Bitumen Mix Design, Chemical and Mechanical Testing Both. etc.
Why Choose This Service
There are no secrets to success. It is the result of preparation, hard work, and learning from failure. So Great things in business are never done by one person. They’re done by a team of people.
Happiness does not come from doing easy work but from the afterglow of satisfaction that comes after the achievement of a difficult task that demanded our best.
“A customer is the most important visitor on our premises. He is not dependent on us. We are dependent on him. He is not an interruption in our work. He is the purpose of it. He is not an outsider in our business. He is part of it. We are not doing him a favor by serving him. He is doing us a favor by giving us an opportunity to do so.”